聯系我們
寧波鐵剛精工機械科技有限公司
地址：寧波余姚市陽明街道康山村仙橋34號
電話：13858213469 18005845696
傳真：0574-62267469
塑料機械
首頁 > 塑料機械
真空洗網 機擠出機網片清洗機 鐵網片清洗機 塑料機網片清洗
真空洗網機Vacuum wash filter machine
一、用途use
本設備專用于塑料擠出過濾網的清洗,按設定參數實現自動清洗過濾網。Equipment for cleaning plastic extrusion filter, according to the set parameters to achieve automatic work.
使用原理及控制.Principle of control.
1。應用塑料類高分子材料在300℃隔絕空氣可裂解焦化,并產生多種裂解物,高于400℃在空氣中可完全氧化的特點;把被清洗的網片加熱到300℃左右,讓工件表面上數量較多的塑料溶化流入到下部積料箱,自動啟動真空泵接著把溫度逐步升到450℃左右,并通過水噴淋洗滌器將灰塵及生成的氣體抽出由水帶走,按設定的工藝進入少量空氣可使其充分高溫氧化生成二氧化碳和灰排出.According to the plastic at 300 ℃ isolated air crackable coking, and produce a variety of lysates, higher than 400 ℃ in the air can be completely oxidized characteristics; the cleaned mesh heated to about 300 ℃, so that the surface of the mesh more Plastic melt into the accumulation box, start the vacuum pump after the temperature gradually rose to about 450 ℃, and through the water spray scrubber, the dust and the generated gas out of the water away by the set process into a small amount of air can make it Full high temperature oxidation to produce carbon dioxide and ash discharge.
2.采用溫度和時間控制方式,實現參數設定下的自動控制,由精密溫控制溫度條件,啟動泵輔工作,時間繼電器控制所處理網片上不同種類塑料所需要時間(3-5小時).Using the temperature and time conditions, the parameters set automatically control.Intelligent temperature controller set to start the pump auxiliary work, time relay control takes time (3-5h).
特點：環境友好Environmentally friendly、
制造工藝先進和選用航天航空材料Advanced manufacturing technology and selection of aerospace materials
節能50%Energy saving 50%
效率提高60%Increased efficiency by 60%
體積減少70Volume reduction of 70%
設備配置的技術參數如下表Technical Data Sheet:
|
型號Model 參數項目Project |
TGSK-ZW200 |
TGSK-ZW300 |
TGSK-ZW500 |
|
工作室容積Studio Volume(L) |
200 |
360 |
600 |
|
電源電壓Power Supply(V-HZ) |
380-50 |
380/50 |
380/50 |
|
加熱功率 Heating Power(KW) |
12 |
20 |
30 |
|
最高溫度Maximum Temperature(℃) |
480 |
480 |
480 |
|
真空泵功率Vacuum Pump（KW） |
1.5 |
4 |
5.5 |
|
溫控精Temperature control Accuracy(℃) |
±1 |
±1 |
±1 |
|
工作周期Working Period(h) |
3-5 |
3-5 |
3-5 |
|
工作方式Work Style |
連續continuous |
連續continuous |
連續continuous |
|
外型尺寸Dimensions（cm） |
130*70*116 |
145*105*116 |
195*105*205 |
|
重量(kg) |
550 |
950 |
1250 |
使用原理及控制.Principle of control.
1。應用塑料類高分子材料在300℃隔絕空氣可裂解焦化,并產生多種裂解物,高于400℃在空氣中可完全氧化的特點;把被清洗的網片加熱到300℃左右,讓工件表面上數量較多的塑料溶化流入到下部積料箱,自動啟動真空泵接著把溫度逐步升到450℃左右,并通過水噴淋洗滌器將灰塵及生成的氣體抽出由水帶走,按設定的工藝進入少量空氣可使其充分高溫氧化生成二氧化碳和灰排出.According to the plastic at 300 ℃ isolated air crackable coking, and produce a variety of lysates, higher than 400 ℃ in the air can be completely oxidized characteristics; the cleaned mesh heated to about 300 ℃, so that the surface of the mesh more Plastic melt into the accumulation box, start the vacuum pump after the temperature gradually rose to about 450 ℃, and through the water spray scrubber, the dust and the generated gas out of the water away by the set process into a small amount of air can make it Full high temperature oxidation to produce carbon dioxide and ash discharge.
2.采用溫度和時間控制方式,實現參數設定下的自動控制,由精密溫控制溫度條件,啟動泵輔工作,時間繼電器控制所處理網片上不同種類塑料所需要時間(3-5小時).Using the temperature and time conditions, the parameters set automatically control.Intelligent temperature controller set to start the pump auxiliary work, time relay control takes time (3-5h).
